Format: x.y.z
x - Added functionality which is backward incompatible.
y - Added functionality which is backward compatible.
z - Backward compatible bug-fixes.

3.0.0
Build Completed: 29 May 2024
Minimum THCC version: 2024.1
Internet connection required during installation!

Highlights
* New model 'Synchronous Motor Current Source' with support for Dynamic Flux.
* Added support for Synchronous Reluctance Motors (SynRM).
* Improvements in iC7 Frequency Converter.

Known Issues
* CIO flags popping up once in a while after stepping up to THCC2023.4. Reported to Typhoon HIL. 


2.0.0
Build Completed: 25 January 2024
Minimum THCC version: 2023.4 sp1
Internet connection required during installation!

Highlights
* Readout of parameters in mask for LC and LCL filter.
* ddCommunication wheel updated to meet the requirements for python 3.11.
* Motor and loads models updated to have TnomInv = 1/Tnom in parameter bus.
* Motor and Inverter thermal models updated with enable input.
* Libraries in Schematic Editor and HIL SCADA restructured and components renamed.

Known Issues
* iC7 Frequency Converter: CIO flags popping up once in a while after stepping up to THCC2023.4


1.0.2
Build Completed: 18 October 2023
Minimum THCC version: 2023.3 sp1
Internet connection required during installation!

Highlights
* iC7 FC can simulate with both HIL402 and HIL404 devices.
* Calibration of HIL Compatible iC7 Frequency Converter.
* Added stand-alone mechanical load models and SCADA widgets for: basic motion load, gear mode, position load, and two mass load.
* Updated 'Basic Load' with posibilites for simulating 'High Starting Torque' and 'Wind Milling'.
* Updated 'Grid With Droop' to run on FPGA, removing stair-case waveform.
* Fixing bug in basic grid widget and added posibility for more types of grid faults and specifying amount of unbalance.
* iC7 FC adding DcLink terminals with posibility to feed from DC source.
* iC7 FC better support for testing of fans (FX09 - FX12).
* iC7 FC fixing gain and offset for grid voltages to have correct measurements (FX06 - FX12).


---
1.0.1
Build Completed: 27 June 2023
Supported THCC version: 2023.2

Highlights
* Fix: iC7 Frequency Converter and VLT Frequency Converter libraries updated to ensure data stored in model would percist after reload of model and libraries
* Fix: Virtual '1500 A HIL' Frequency converter could not power up due to error in PUD file


---
1.0.0
Build Completed: 26 June 2023
Supported THCC version: 2023.2

Highlights
* Initial release of MyDrive HIL for iC7 Frequency Converters
* Including 1500 A iC7 Frequency Converter for testing purpose. Not a real iC7 variant!
* Package installation through Typhoon HIL Package Manager

Breaking Changes
* Not compatible with previous versions! 


---
0.0.3
Build Completed: 1 June 2023
Supported THCC version: 2022.4

Highlights
* Added 1 MW VLT Frequency Converter to package for testing purpose. Not a real VLT variant!


---
0.0.2
Build Completed: 25 January 2023
Supported THCC version: 2022.4

Highlights
* Improve torque results at low speed 
* Extend range of squared term for toruque 
* Add torque oscillations for simulating load disturbance


----
0.0.1
Build Completed: 22 December 2022
Supported THCC version: 2022.4

Highlights
* Hello World - Initial release of MyDrive HIL for VLT Frequency Converters
